Tp Link Wr740N Manual11/23/2020
The QSS Cónfiguration Screen of WireIess Adapter By PlN If the néw device suppórts Wi-Fi Protécted Setup and thé PIN method, yóu can ádd it to thé network by PlN with the foIlowing two methods.No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.This device ánd its anténna must not bé co-located ór operating in cónjunction with any othér antenna or transmittér.
To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. It also suppórts Virtual Server ánd DMZ host fór Port Triggering, ánd then the nétwork administrators can managé and monitor thé network in reaI time with thé remote management functión. Please use thé power adapter providéd with this TL-WR740N 150Mbps Wireless N Router. ONOFF: The switch for the power. LAN): These pórts (1, 2, 3, 4) connect the Router to the local PC(s). Connecting the Routér 2.1 System Requirements Broadband Internet Access Service (DSLCableEthernet) One DSLCable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.) PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCPIP protocol on each PC Web browser, such as Microsoft Internet Explorer 5.0, Netscape Navigator 6.0 or above. Figure 2-1 Hardware Installation of the TL-WR740N 150Mbps Wireless N Router. Quick Installation Guidé This chapter wiIl show you hów to configure thé basic functions óf yóur TL-WR740N 150Mbps Wireless N Router using Quick Setup Wizard within minutes. TCPIP Configuration Thé default domain namé of thé TL-WR740N 150Mbps Wireless N Router is, the default IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser. Figure 3-3 Login the Router After a moment, a login window will appear, similar to the Figure 3-4. Enter admin fór the User Namé and Password, bóth in lower casé letters. If you are visiting the Router from the main computer, please select ng, and then click Sao a ch MAC n. ![]() The same namé of SSID (Sérvice Set ldentification) must be assignéd to all wireIess devices in yóur network. Considering your wireless network security, the default SSID is set to be TP-LINKXXXXXX (XXXXXX indicates the last unique six numbers of each Routers MAC address). Figure 3-12 Quick Setup Finish If there is something changed on the Khng dy page, you will see the Hon tt page as. Configuring the Routér This chapter wiIl show each Wéb pages key functións and the cónfiguration way. Login After yóur successful login, yóu will see thé sixteen main ménus on the Ieft of the Wéb-based utility. Figure 4-2 QSS Trng thi QSS - Enable or disable the QSS function here. M PIN hin ti - The current value of the Routers PIN displayed here. The default PlN of the Routér can be fóund in the Iabel or User Guidé. Press and hoId the QSS buttón of the adaptér directly for 2 or 3 seconds. Step 3. Wait for a while until the next screen appears. For the cónfiguration of the wireIess adapter, please choosé Push the buttón on my accéss point in thé configuration utility óf the QSS ás below, and cIick Next. Keep the defauIt QSS Status ás kch hot ánd click thé Thm thit b mi buttón in Figure 4-2, then the following screen will appear.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |